The service of data center cleaning has been a major focus of late for data centers, service companies and end users. This renewed focus on cleaning services is prompted by ASHRAE and manufacturers such as IBM, Dell and HP. None of these well-respected entities would recommend that the service be performed in-house.
Prior to starting Premier Solutions Co. in 1997, I spent 12 years in data centers selling disaster recovery, storage of data via media and data back-up solutions. I continually noticed loose dirt and dust ( particulate) was evident in over 90% of my client base.
Thus, our service called, Data Center Maintenance (DCM) and Premier Solutions Co. was formed. To date, we have cleaned over thirty million square feet of data center flooring, over one hundred thousand server cabinets and over one million servers and systems.
Our service began with little direction from the industry. Very few firms were specializing in offering data center maintenance. We used our knowledge from years of selling IT infrastructure solutions such as UPS, enclosures, KVM switching and power and cooling products to erect a service geared towards protection of the environment and the equipment housed within. We also consulted with tile manufactures on which solutions to use to clean raised flooring.
Many times, the frequency of service was based solely on the client’s budgetand/or lack of knowledge about the effect particulates can have on the data center, IDF, MDF and lab.
For most IT Budgets, 4% is set aside for maintenance within a predictable cost structure and OPEX. The cost of a preventative maintenance program is a fraction of your IT budget and the cost of physical equipment
As IT equipment shrinks in size, resulting in smaller components and less physical space between them, the risk of contamination grows. Increased heat loads per unit volume of air necessitates the need for more airflow, thus, increasing the exposure of electronics to detrimental effects of accumulated dust.
Frequency of Service Recommendations:
HP recommends weekly dry mop and monthly damp mop
SUN recommends quarterly floor surface and hardware decontamination
In today’s high-density, virtualized centers, it is extremely important to keep thefacility within “clean specifications” at all times. To achieve this, it may berequired to have a top floor service done monthly, especially for sites located near freeways. High-traffic areas emit more carbon that will inevitably enter the data center.
Why Clean Servers?
Particulates move at high velocity into the intake of the servers. A low percentage of these particulates make it out of the server vent. Cleaning the faceplate and rear or side vent of the server should occur two to three times annually.
Contaminants And Particulates
It’s important to identify the types of contaminates and particulates in the data center because “cause-effect” solutions are required to keep the OPS running99.9999%. Many contaminates become corrosive due to the humidity in the room. We recommend that data center managers adhere at all times, not just after cleaning, to Ashrae TC9.9 recommendations of ISO14464-1 class 8 specifications. This can be accomplished via proper and frequent filtering of the room.
Has the ability to damage equipment intermittently or permanently
Has the ability to migrate to areas inside of equipment that can cause
Accumulate in large abundance and work their way into the entire
room due to the recycling of air
Can be one of four types, metallic, carbon, construction or corrosive.
Cause: Worn HVAC parts, electrical work, worn raised floor
Effect: The conductive properties are damaging to servers.
Cause: Outside carbon from autos, printers or paper dust
Effect: Humidity in the data center transforms the carbon particulate into a conductive material which is damaging to servers. Carbon particulates can also be found in ceilings due to return airflow.
Cause: Sheet rock, unsealed sub floor, cement
Effect: Abrasive material that travels at high rates of speed via recycled airflow.
** Progressive cleaning thru the stages of construction are recommended
Use of “proprietary” cleaning solutions
Use of “Specially formulated products”
Using water to clean sub-floor (water and 480V don’t mix) Keep water source off of the computer room floor
Cable cutouts in server cabinets used to cool the cabinet Floor tiles stripped and waxed
Improper sub-floor process
Caring For The Data Center
Utilize clean step-mats at doorways
Clean CRAC unit filters
Use particle testing as a gauge of environment condition
Close off server cabinet cut outs
Have delaminated or trip tiles replaced
Place perforated tiles in cold aisle/front of cabinet
Inspect water cooling units regularly
Disallow cardboard and pallets in center
Removal and repair of sub floor corrosives
Clean cabinets and hardware twice annually. Dust can create an
“insulative layer” that will lead to heat related failures
Clean sub floor twice annually
Why Clean Ceiling tiles?
For the data center using re-circulating air, the contaminates within the ceiling plenum make their way into the intake of the CRAC/HVAC in a short period of time and at a high velocity. Gauge the type of particulate captured in the HVAC filter and the duration of filter life to determine the needs for your ceiling.
We all know that data centers accumulate loose particulates. We know they travel through the center and make their way into the servers. Now more than ever, detailed due diligence is required. A regularly scheduled service with parameters in place and the identification of particulates will allow your data center to stay in optional health.
This document is copyright © 2018 Premier Solutions Co. No part of this publication may be reproduced by any method whatsoever without the prior consent of Premier Solutions Co.
Due to the nature of this material, numerous hardware and software products have been mentioned by name. In the majority, if not all, of the cases, these product names are claimed as trademarks by the companies that manufacture the products. It is not Premier Solutions Co.’s intent to claim these names ortrademarks as our own. Likewise, company logos, graphics or screen shots have been reproduced with the consent of the owner and are subject to thatowner’s copyright.
Whilst every care has been taken in the preparation of this document to ensure that the information is correct, the publishers cannot accept responsibility for any errors or omissions.